dark

OpenWRT – NanoPi R4S 概述和性能测试（NAT、OpenVPN、Wireguard、iPerf）

Total
0
Shares
0
0
0



在本视频中，我们将了解 NanoPi R4S 并检查 OpenWRT 的设备性能。 测试包括 NAT（WAN 到 LAN 吞吐量，OpenSpeedTest & iPerf3、OpenVPN 和 Wireguard VPN。NanoPi R4S 是一款小巧但功能强大的 SBC，采用六核 Rockchip RK3399 SoC，频率最高可达 1.8GHz。它配备 1GB 和4GB LPDDR4 RAM 版本。具有 2 个千兆以太网端口和 2 个 USB 3.0 端口，NanoPi R4S 适合用作网关路由器。以下是测试结果的简短摘要 – NanoPi R4S WAN to LAN 吞吐量：934 Mbps at 80% CPU 空闲 – NanoPi R4S OpenVPN 吞吐量：在 80% CPU 空闲时为 200 Mbps – Nano Pi R4S Wireguard VPN 吞吐量：在 53% CPU 空闲时为 200 Mbps OpenVPN 和 Wireguard VPN 吞吐量应该更高，但我已经达到了我的互联网计划的限制。查看视频，了解有关 R4S 及其性能的更多信息。视频时间范围：00:00 – NanoPi R4S 介绍 00:21 – NanoPi R4S 连接器概述（以太网 – USB – microSD） 01:43 – NanoPi R4S 上的 Rockchip RK3399 SoC 02:03 – NanoPi R4S 的电源适配器 02:32 – NanoPi R4 支持的操作系统 S 02:45 – 在 NanoPi R4S 上安装 OpenWRT 03:01 – 使用 OpenWRT 命名 NanoPi R4S 网络接口 04:06 – 在 NanoPi R4S 上使用 OpenSpeedTest 进行 WAN 到 LAN 吞吐量 08:08 – 在 NanoPi R4S 09 上使用 iPerf3 实现 WAN 到 LAN 吞吐量： 20 – NanoPi R4S WAN 到 LAN 的吞吐量禁用软件卸载 12:36 – NanoPi R4S Wireguard VPN 吞吐量测试 14:07 – NanoPi R4S OpenVPN 吞吐量测试 14:57 – 我对 NanoPi R4S 资源的想法：NanoPi R4S OpenWRT 快照固件 (openwrt .org) – https://downloads.openwrt.org/snapshots/targets/rockchip/armv8/ 树莓派电源适配器 – 5V/3A – USB type C- https://www.cytron.io/p-official-rpi -15w-5v-3a-psu-usb-c-eu-plug-white?tracking=vantech NanoPi R4S 主页 – https://www.friendlyarm.com/index.php?route=product/product&product_id=284 NanoPi R4S来源和图片（friendlyarm）- https://dl.friendlyarm.com/nanopir4s 感谢观看，再见！ .

26 comments

  2. Can you setup the Multi Van (means we can multi dial our ppoe connection) so we can 3X or 4X our bandwidth? I saw some Chinese people do it, but it's in Chinese, very hard to understand.

  3. I think your VPN test results are limited by VPN providers (or WAN link) but not a good measure of real throughput of the router. Can you setup a local VPN to get the good result?

  7. One thing to try is as others said, SQM, but also, try iperf3 in –bidir mode, or two iperf running to each other across the router so you load up and downlink simultaneously, this is usually when you run into interesting bottlenecks.
    Not sure if the NICs in this supports Recieve side scaling, so might still be stuck with two cores loaded

  8. Do you have any alternative suggestion to HP T620 Plus? I want a openwrt router that can handle gigabit speeds and run sqm cake. I read a lot about nano pi r4s and many more but they all take too long to ship or some of them are just out of stock.

  11. Nanopi R2S can do SQM at 300 + Mbps with 40 percent cpu usage ( cake and piece of cake),not sure about 1 Gbps , can you please check this .

  14. @Van Tech Corner  what router do you guys suggest for openwrt I wanna use sqm and cake with 1gigabit connection so I can at least get 900+Mbps with sqm and cake is enabled any suggestions?

  15. Since this sbc has 6 cores (4+2), i wonder if you load balance the traffic, it will use all cores or just either 4 cores (a53) or 2 cores (a72) only.

    Load balance traffic by enabling Packet steering

  16. Bro, you should try with enabling Packet Steering. Network->Interfaces->Global Network Option.

    By enabling this, it will load balace all cpu. It will greatly reduce cpu temperature and none of the cores should go to the max.

    I love to see such result.

  17. Hi Van , I would be highly obliged if you can check that Nanopi R2S and R4S with cake and piece of cake as trafic scheduler( default cake configuration) can handel 1 Gbps with this ,wnated to buy one of as router replacement.

  23. Can you run iperf3 with client option -t60 or longer I use -t300 ( 5 minutes) the default time of -t10 is too short to test cpu load and saturate the interface to generate errors. Also test with -R to run in reverse mode.

Comments are closed.